Naiad G3

  • Low construction
  • Many sizes & variants
  • Made in Värnamo, Sweden
Product description

Naiad G3

Naiad is a low-built all-round luminaire that meets the requirements for D-labeling. The luminaire is well suited as general lighting through an opal diffuser with controlled glare in, for example, industries, warehouses and garages.
When mounted with the supplied gaskets, the luminaire achieves protection class IP44; when mounted on a wall or without gaskets, the luminaire achieves protection class IP40. Note, however, that variants with PIR have a protection class of IP42.

The luminaire is available in four different sizes, 350, 602, 1202 and 1502mm with different controls, on/off, DALI, RS, RS DIM, PIR and BTDA. The luminaire is also available in variants with emergency light, override and with high luminous flux (HO).

On/off
DALI can be connected as DALI or as impulse control/Switch-dim.
RS is equipped with a motion sensor that turns on the luminaire when there is a presence and turns off the luminaire if no presence is registered during the set delay time (5 minutes).
The sensor can also detect movement through, for example, glass and walls (not metal) and can be sensitive to vibrations, ventilation and the like. Luminaires with RS can also operate luminaires without RS (slave luminaires, on/off), but a maximum of five slave luminaires per luminaire with RS (sensor). Luminaires with RS are best suited for ceiling heights up to 4 meters.
RS DIM makes it possible to have a reassuring basic light of, for example, 10% with a transition to 100% brightness in case of movement. After a set time without movement (5 minutes) the luminaire returns to 10%. On request, RS DIM is available with programmed switch-off or other settings for basic light and delay time. Luminaires with RS DIM can also operate luminaires without RS (slave luminaires, DALI), but a maximum of five slave luminaires per luminaire with RS DIM (sensor). Luminaires with RS DIM are best suited for ceiling heights up to 4 meters.
PIR reacts to both motion and heat. The delay time is factory set to 5 min but can be ordered with the following time: (5 s, 1 min, 10 min, 15 min, 30 min and 60 min). The PIR sensor also has a light sensor that can be set so that the luminaire only turns on when the ambient light level is below the set threshold. Luminaires with PIR are best suited for ceiling heights up to 4m. The relay in Naiad PIR can handle a maximum of 6 actuators, which must be taken into account for any slave luminaires (the number applies to luminaires with electronic actuators).
The light sensor is deactivated from the factory but can be activated with a remote control (7009046) available as an accessory. The same remote control can also be used to change the delay time.
PIR DIM makes it possible to have a reassuring basic light of 10% with a transition to 100% brightness in case of movement. After 5 minutes without movement, the luminaire returns to 10%. As an option, the luminaire can be programmed with another holding time and other light levels. Luminaires with PIR DIM are best suited for ceiling heights up to 4m. The relay in Naiad PIR DIM can handle a maximum of 6 actuators, which must be taken into account for any slave luminaires (the number applies to luminaires with electronic actuators).
The light sensor is deactivated from the factory but can be activated with a remote control (7009046) available as an accessory. The same remote control can also be used to change the delay time.
BT has a microwave sensor (RS) with Bluetooth communication for on/off. The sensor can control everything from individual luminaires up to complex lighting installations.
The luminaires are easily configured via an app and communicate wirelessly via mesh networks. Easily mounted with keyholes in the frame and installed with new or existing cabling without control wires.
BTDA enables wireless control and grouping of luminaires using Bluetooth. The luminaires are easily configured via an app and communicate with each other through a mesh network that relays information via the other luminaires. Luminaires with BTDA provide a stable signal strength and are also suitable for environments that may be difficult for radio signals, such as brick and concrete building materials.

NÖD has a built-in emergency light (1 hour).

The luminaire is manufactured in Värnamo.

Download product data sheet Download documents

The icon shows that the product can be customised according to your needs: special colour, luminous flux and control. Depending on the product, the customisation options may differ.

Read more
Request a quote

Do you want to customize the product? Submit your requests and we will contact you!

Filter variants

Max active values:
Downloads
Your document collection

Document